EN6001 Constant Current AC Controls

The EN6001 is a versatile Single Phase AC control. Among its many features, 64 Weld programs, that can be executed as single sequences or chained to produce a variety of sequences. Constant Current – using primary or secondary sensor. The EN6001 provides 3 valve outputs can be used for multi-welding, or other functions depending on application requiring outputs before/after the weld. In additional 6 Programmable inputs and 4 Programmable outputs allow selection of assigned functions such as Retract, Parts counter management, Lockout. The EN6001 Includes a USB port for updates or backups. An Optional Ethernet adapter is available for automation using Ethernet IP control, or Modbus TCP/IP or full data exchange and I/O control. ENLINK 6001 Software is available for programming and monitoring via PC.

Please refer to the EN6001 Bulletin

Learn more about the EN6001 Retro Fit Kit

newslide en6001 retrofit

 
 

Processes Supported by Control

Spot Weld

Spot Repeat weld

Spot Pre Heat with Pulses

Projection Weld with Tooling

Crosswire Welding

Seam Weld

Hotstaking/Rivet Weld

Butt Weld Post Heat

Butt Weld Single Heat

 

Details

Options

  • Program Lockout (key switch)
  • Weld/No Weld Switch
  • Water Flow Switch
  • Counter Reset Pushbutton
  • Optional Mode Switch (program Lockout and Weld/No Weld)
  • Plug-in Ethernet card provides PLC compatibility via Modbus and E/IP for remote I/O

Technical Specifications

BENEFITS:

  • Low cost
  • Easier to program
  • More I/O
  • USB backup Port
  • Schedule Number: 0 to 63
  • Squeeze Delay: 0 to 99 cycles
  • Squeeze: 0 to 99 cycles
  • Valve Mode: None / All combinations of 3 valves
  • Weld1: 0 to 99 cycles
  • Weld1 Current Regulation Mode: Phase Shift / Constant Current
  • Heat1: 0 to 99%
  • Current1: 0 to 100.00 kA
  • Cool1: 0 to 99 cycles
  • Slope: 0 to 99 cycles
  • Weld2: 0 to 99 cycles
  • Weld2 Current Regulation Mode: Phase Shift / Constant Current
  • Heat2: 0 to 99%
  • Current2: 0 to 100.00 kA
  • Cool2: 0 to 99 cycles
  • Hold: 0 to 99 cycles
  • Off: 0 to 99 cycles
  • Impulses: 1 to 99 cycles
  • Heat/Current Offset: -15 to +15%
  • Cycle Mode: Non-repeat / Repeat / Chained / Successive / Wait-here

Features

  • Constant current regulation; Primary / Secondary feedback
  • Phase shift monitor
  • Current monitoring with high, low, and pre-limits
  • Up to 64 programs (internal or 16 external selection)
  • Six (6) inputs and four (4) outputs with output protection on CPU
  • Electrode management functions, including stepping, tip-dressing and preset curves
  • Welding programs may be linked together for complex spot schedules (chained or successive) Refresh firmware through USB device
  • Load/export control settings from/to USB device
  • AC 60/50 Hz welding supported
  • Spot / Pulsation / Seam welding / Flash or Butt welding / Brazing
  • Multiple weld intervals plus pulsation, upslope and downslope
  • Air-over-oil gun operation
  • Retraction – maintained, and momentary
  • Water Saver (contactor timer)
  • Head lock function
  • Half-cycle operation (Alt. / Pos. / Neg.)
 

Find out more

Let Our Team Answer Your Questions About The EN6001 Constant Current AC Controls